Mixture Formation in Internal Combustion Engines

This book covers the various approaches to modelling and optimising the spray and mixture formation processes in modern internal combustion engines. Due to their complexity and importance in predicting the temporal and spatial distribution of liquid and gaseous fuel inside the cylinder, special emphasis is put on the detailed description of multi-dimensional CFD-models.

Mixture Formation in Internal Combustion Engines

Baumgarten,Carsten

Springer-Verlag Berlin Heidelberg

2006

Abstract

This book covers the various approaches to modelling and optimising the spray and mixture formation processes in modern internal combustion engines. Due to their complexity and importance in predicting the temporal and spatial distribution of liquid and gaseous fuel inside the cylinder, special emphasis is put on the detailed description of multi-dimensional CFD-models. The book describes and discusses the most widely used mathematical models for in-cylinder spray and mixture formation processes. These processes are the most important sub-processes today affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic and fluid dynamic processes are summarized, and then the application to the in-cylinder processes is described. Although the combustion and formation of emissions are not part of this book, the effects of the different mixture formation concepts on the combustion process are always included.

After the introduction (chapter 1), the fundamentals of mixture formation like injection systems and nozzle types, break-up regimes of liquid jets and droplets, semi-empirical relations and basic experimental investigations are summarized in chapter 2. Hence, this chapter provides the reader with the basic knowledge in order to facilitate the comprehension of the following parts. In the third chapter the basic conservation equations which are necessary for the three-dimensional simulation of mixture formation are derived. This chapter includes the relevant equations for the description of the continuous phase (Eulerian description, conservation equations, turbulence modelling) and the dispersed phase (Lagrangian description, spray equation, Monte-Carlo-Method and stochastic-parcel-method).

The three-dimensional CFD modelling of primary and secondary spray break-up, evaporation, turbulent dispersion, collision, wall impingement and ignition is presented in detail in chapter four. Example calculations are compared with semi-empirical relations and corresponding experimental data - represented in diagrams as well as in images resulting from modern optical measurement techniques - in order to discuss the capabilities of today’s simulation models as well as their shortcomings.

Chapter five is about the influence of grid resolution on the numerical computations of jets. The Problem of defining an optimal grid size as well as approaches to reduce the grid dependency are discussed.

The last chapter deals with modern strategies for mixture formation and combustion processes. Today’s and future requirements concerning the development of injection systems capable of optimising the combustion process in terms of reduced fuel consumption and emissions are discussed. Mixture formation concepts like gasoline direct wall-guided, air-guided and spray-guided injection techniques, variable rate shaping, variable needle lift, modulation of injection pressure as well as the application of homogeneous charge compression ignition concepts are described and compared with experimental data.

Citation

Baumgarten, Carsten. Mixture formation in internal combustion engines. Springer Science & Business Media, 2006.

Collection

Công nghệ ô tô

Related document

Mixture Formation in Internal Combustion EnginesMechatronic modeling and simulation using bond graphsAutomotive diagnostic fault codes techbook
Mixture Formation in Internal Combustion EnginesMechatronic modeling and simulation using bond graphsAutomotive diagnostic fault codes techbook

QR code

Mixture Formation in Internal Combustion Engines

Content

  • Thứ Hai, 13:42 05/07/2021

Tin tiêu điểm

THÔNG BÁO V/v cấp tài khoản truy cập thư viện số ĐH Công nghiệp Hà Nội

THÔNG BÁO V/v cấp tài khoản truy cập thư viện số ĐH Công nghiệp Hà Nội

Thứ Sáu, 15:09 30/09/2022

Giới thiệu về các hoạt động, dịch vụ của Thư viện cho hơn 800 tân sinh viên hệ Cao đẳng - K24 trong chương trình “Tuần sinh hoạt công dân - sinh viên đầu khóa năm học 2022 - 2023”

Thứ Năm, 13:42 15/09/2022
Trung tâm Thông tin Thư viện trân trọng thông báo tới bạn đọc về việc cung cấp dịch vụ hỗ trợ tìm kiếm tài liệu điện tử

Trung tâm Thông tin Thư viện trân trọng thông báo tới bạn đọc về việc cung cấp dịch vụ hỗ trợ tìm kiếm tài liệu điện tử

Thứ Năm, 08:04 25/08/2022
Trung tâm Thông tin Thư viện trân trọng thông báo tới bạn đọc về việc cung cấp tài khoản truy cập nguồn tin Khoa học - Công nghệ

Trung tâm Thông tin Thư viện trân trọng thông báo tới bạn đọc về việc cung cấp tài khoản truy cập nguồn tin Khoa học - Công nghệ

Thứ Hai, 08:25 15/08/2022

Tập huấn sử dụng phần mềm và khai thác tài nguyên thư viện phục vụ nghiên cứu, học tập và giảng dạy

Thứ Tư, 15:27 06/04/2022

Các bài đã đăng

Practical business math procedures tenth edition

Thứ Ba, 00:00 27/09/2022

Coach yourself to success: Winning the investment game

Thứ Sáu, 14:08 23/09/2022

Great again : Revitalizing America's entrepreneurial leadership

Thứ Sáu, 14:05 23/09/2022

Principles of micro economics. secand edition

Thứ Sáu, 09:51 23/09/2022

Cao điểm mùa hạ; Một chiều xa thành phố

Thứ Ba, 11:04 20/09/2022

Mechanical Measurements

Thứ Hai, 13:27 05/07/2021

Mechanical Measurements

Thứ Hai, 13:08 05/07/2021

Automotive Air-conditioning and Climate Control Systems

Thứ Hai, 12:56 05/07/2021

Hackers TOEIC Reading - Actual Tests

Thứ Hai, 09:48 05/07/2021

Luyện kỹ năng nghe, nói và phát âm tiếng Anh

Thứ Hai, 09:22 05/07/2021

Video giới thiệu